Figure 8 Fiber Cable: Aerial Runs with an Integrated Messenger

Figure 8 Fiber Cable: Aerial Runs with an Integrated Messenger

A figure 8 fiber cable carries its own messenger, so the span hangs in one pass. When it beats ADSS, how to size the span, and what the lashing crew needs.

A figure 8 fiber cable is a loose-tube cable and a steel messenger joined in one sheath shaped like the numeral 8. The crew hangs the whole assembly in a single pass — no separate lashing of a bare cable to a pre-strung wire — which is why short and medium aerial spans so often specify it. The design decision is not figure 8 or nothing; it is figure 8 versus all-dielectric ADSS versus cable-plus-separate-messenger.

Figure 8 vs ADSS vs separate messenger

OptionStrength memberBest fitWatch out for
Figure-8 self-supportingIntegrated steel messengerPole-to-pole campus and access spans where a single pass mattersSteel messenger needs bonding/grounding near power lines
ADSSAramid yarn, all-dielectricShared power corridors, long spans, dry-zone trackingSpan and sag must be engineered per tower
Cable + separate messengerStranded steel wireRoutes where the messenger already existsTwo-pass installation, higher labor cost

Sizing the span before ordering

  • Span length and sag. State pole spacing and allowable sag — the messenger grade and cable construction are selected against the worst span, not the average.
  • Ice and wind load. Ice-covered or high-wind routes move to a heavier messenger; the quote should carry the load case you specify.
  • Existing hardware. Suspension and tension clamps must match the messenger diameter — send the hardware list with the inquiry.
  • Grounding plan. The steel messenger must be bonded per the site's earthing rules wherever it runs near equipment.

Termination at the ends

Terminate the loose-tube side indoors with pigtails and an adapter panel, as in our pigtail termination guide; the messenger ends on its own clamp at the entrance bracket. Separating the two terminations is what keeps future re-patching cheap.

Key specifications at a glance

ParameterTypical value
FiberG.652D single mode, 2–144 cores typical
Attenuation≤0.36 dB/km @1310 nm / ≤0.22 dB/km @1550 nm (typical, per datasheet)
StructureLoose tube + integrated steel messenger, figure-8 cross-section
Temperature−40 °C to +70 °C (typical)
MOQPer-reel order, factory-cut lengths
Lead time7–15 working days after deposit
Payment30% T/T deposit, balance before shipment
Warranty12 months from shipment date

Values marked typical are industry reference figures; the shipped datasheet governs each build.

Buyer FAQ

Can figure 8 cable run on shared power poles?

Physically yes, but the steel messenger near live hardware demands bonding and clearance discipline. Many operators choose ADSS on shared corridors precisely to remove the metal.

What span length is figure 8 good for?

It depends on the messenger grade and load case. Short campus spans are routine; for long crossings send the span, sag and load data so the build is engineered rather than guessed.

Do we order it by reel or by cut length?

Both are possible: standard reels for stock, factory-cut lengths for engineered routes. Cut lengths reduce mid-span splices on straight pole lines.

Ferramenta de decisão

Que construção aérea se adequa ao seu vão?

Escolha a decisão de vão — a resposta reitera as regras aéreas nesta página.

Solicitar uma cotação de solução

Descreva o seu cenário de implementação, os tipos de conector necessários, as contagens de fibra e as quantidades pretendidas. Quanto mais específicos forem os seus dados, mais rapidamente os nossos engenheiros poderão confirmar os produtos correspondentes e o prazo de entrega.

Consulta de Produto
◆
Consulta de Produto
Figure 8 Fiber Cable: Aerial Runs with an Integrated Messenger (figure-8-self-supporting)